Tips – Body

 

Body

Hinge Pin Removal
Bud Vases
Headlamp Bar Fitting

 

Removing Difficult Hinge Pins

In order to fit my new external mirrors to my Sports Coupe, the top hinge pins needed to come out.  After a week of spraying them with Break Away (my latest highly recommended penetrating spray), and thumping them with a pin punch and gympie, they hadn’t budged.

After searching the internet, canvassing expert and non-expert opinions, I was almost at the stage of trying to remove the hinges (would that have been any easier?), using heat, and re-painting them.

Then in the wee hours of one morning (when I thought I was asleep), I came up with the successful solution.  It involved the use of my cheap, monster 1500W hammer drill/jack hammer (pictured).

Using my normal drill, I drilled a small dimple in the bottom of the hinge pin to try to stop the pointed chisel tip from sliding off.  Because I couldn’t get the big jack hammer directly under the hinge, and it was always going to jump off towards the car, I notched a piece of wood for my accomplice to hold to keep the chisel tip in position.

After that preparation, one pin took about 10 seconds of high pressure and heavy percussion before it popped-free, while the other came free very quickly.

Sadly, it appears Bunnings don’t sell this beast anymore.  My recollection is that it only cost about $100 about 8 years ago.  If you need to drill through concrete and your normal hammer drill is struggling – this thing makes short work of it.  And if you need to breakup brickwork, the big chisel tip slices through mortar.

I didn’t think to take a photograph of this at the time, so this “after the event” shot shows the chisel tip under the new mirror bolt instead of under the old hinge pin.

Ian Steer, MARC WA Newsletter July 2018
Top of page

 

Bud Vases for Closed Cars

For those interested in a pair of Bud Vases for their closed car who find the price (US$195) a little high for repro units considering what they are, and baulk at the cost of original sets, this hint offers a good alternative.

If you are savvy in using Ebay, you may find the search criteria “bud vase” not very productive and, if original car bud vases are found, very expensive.  Try your search using the word “epergne”.  Epergne is often used to describe a bud vase as used in a house, but luckily for us sometimes epergne is used to describe original vintage car bud vases.  If your search does not yield a set of original car bud vases and you are impatient, then with a little imagination, patience and research you could find pairs of small house vases in a very wide range of designs, colours and sizes that may be just as suitable.  Look for pairs.

You will probably need to fabricate a bracket or, alternatively, Snyders sell brackets if you are sure the epergne vase will fit.

Hint: Remember those chrome stand tea candle holders popular a few years ago?  The individual candle holders are perfect as brackets.  These litter your local Salvo or Good Sammy shop for $1, and with a little effort you can make many brackets from one stand.

Be aware: Most epergne on offer will be household flower display vases and as such not suitable for our use.  So for something which looks promising, it is important you seek a full description, including dimensions and overall appearance, and you will need to consider how you will attach the bracket to your car.

I am sure you will find something unique for your Model A closed car for much less than the standard repro car bud vases on offer.

If it all sounds too challenging Snyders have nice bud vase sets and brackets to suit for US$195 vase pair + US $49.95 brackets.

Fred Manwaring, MARC WA Newsletter June 2012
Top of page

 

Headlamp Bar Fitting

Sometimes when you fit the headlamp bar to the mudguard stays, the bolts do not drop in without excessive force.  To achieve an easier fit, you can spend lots of time with trial and error bending the mudguard brace.

To overcome this problem, I made up two 1mm steel shims to fit between the chassis and the mudguard brace.  This spaces the braces out slightly and allows the bolts to push in without force.  Everything is then in a neutral position and it certainly makes installing the rubber pads easier.

Trial shim made of Colorbond

Final piece was made out of galvanised steel sheet, with a better finish on the edges and holes.


Ron Andrews, MARC WA Newsletter, December 2019

Top of page